Automatic Fire Suppression for Mining, Civil, and Off-Road Equipment

A fire on a haul truck or an excavator rarely starts where anyone can see it. It starts in an engine bay caked in oil and rock dust, behind a turbo running hot after a long grade, or inside a hydraulic compartment holding a pressurized line that finally lets go. The machine is often alone at a pit face or a job site at the far end of a project, and by the time anyone in a cab three hundred yards away notices smoke, the fire already has everything it needs.

BlazeCut protects that machine automatically, whether it's an engine bay, a hydraulic compartment, or an electrical enclosure, with no operator, no wiring, and no control panel required to catch it in time.

How Does The T-Series Work?

A diagram of the t-series automatic fire suppression system from BlazeCut

The BlazeCut tube is the detector and the extinguisher in a single sealed unit, installed directly inside the compartment it protects. Every point along the tube senses heat continuously.

When any point reaches the actuation threshold, the tube ruptures at that exact location and discharges the agent directly onto the ignition source, whether that's a turbocharger on a haul truck or a hydraulic pump on an excavator, before it spreads to the rest of the machine.

No power required. The T-Series operates independently of any electrical supply, which matters on equipment running unattended at a pit face, a quarry bench, or a remote grading site with no one nearby.

Sealed and rated for harsh duty. Stainless steel fittings and a tube rated for a service life of up to 10 years, with no scheduled maintenance requirement, built for equipment that runs in rock dust, mud, and vibration all day.

Sized to the equipment. Available in lengths from 10 inches to 26 feet, covering roughly 3.5 to 141 cubic feet, so the same product line fits an engine bay, a hydraulic compartment, or an electrical cabinet on anything from a skid steer to a rigid-frame haul truck.

Typical Installation Points on Mining and Off-Road Equipment

Engine & Hydraulic Systems

  • Engine compartments on haul trucks, excavators, dozers, and wheel loaders
  • Hydraulic pump, valve, and cylinder compartments on excavators and articulated dump trucks
  • Turbocharger and exhaust manifold areas prone to hot-surface ignition on graders and scrapers

Processing & Crushing Equipment

  • Crusher and screen plant drive compartments
  • Conveyor drive and gearbox housings
  • Portable crushing and screening unit engine bays

Electrical & Battery Systems

  • Electrical and control cabinets on fixed and mobile mining equipment
  • Battery compartments on electric and hybrid mining and construction equipment
  • Drill rig and auxiliary generator control enclosures

Protecting Your Fleet, Your Equipment, & Your Crew

A single system protects one machine. A fleet-wide rollout protects the pit, the site, and the contract. We work directly with mining operators, civil contractors, and equipment fleets to size systems across a full equipment list and structure pricing for fleet and multi-site deployments.

Contact Dalton at dalton@blazecutusa.com to scope a fleet or contract-driven deployment.

What BlazeCut Saves You

  • MONEY

    A single equipment fire can take out an engine, a hydraulic system, or a full machine, along with the production schedule it was supporting. A fire that spreads off the machine adds suppression costs, site damage, and liability exposure on top of the equipment loss. Fleet-wide suppression turns an unpredictable loss into a fixed, budgeted cost.

  • DOWNTIME

    A fire contained inside the compartment it started in is a short stop and a work order. A fire that spreads is a machine off the site for weeks, a rental unit to source, and a production deadline at risk. Suppression at the source is what keeps one hot surface from turning into a lost month.

  • TIME

    No one has to notice the smoke, reach a handheld extinguisher, and get close enough to use it safely, especially on a machine running alone at a pit face or a remote grading cut. The system is already inside the compartment, sensing heat continuously, and it discharges the moment it detects ignition, whether or not anyone is on the machine or on site.


  • SAFETY

    Nobody has to approach a burning engine bay or a machine that's already smoking to deal with it. The system suppresses the fire before it grows, which means less exposure for the operator and less risk that a small mechanical fire turns into something the whole crew has to evacuate from.

  • EFFORT

    There is no control panel to program, no wiring to run, and no scheduled maintenance to track. The T-Series is installed once, inside the compartment it protects, and it works independently of any electrical supply for up to 10 years, on equipment that is expensive and inconvenient to pull out of rotation for inspection.

  • PEACE OF MIND

    Once it is installed, it works whether the machine is running a double shift alone in a pit or sitting overnight on a laydown yard. A fleet with suppression built into every high-risk compartment is a fleet where one hot surface doesn't turn into a site shutdown and an incident report.

1 6

  • LPS 1666, LPCB approved. LPCB (the Loss Prevention Certification Board, part of BRE Global in the UK) is one of the most established third-party fire testing and certification bodies internationally, and its approval is widely recognized and accepted by insurers and AHJs.
  • CE Mark. Certifies the system meets applicable EU health, safety, and performance requirements, independently verified.
  • Independently performance tested at an accredited testing institute, Strojírenský zkuÅ¡ební ústav, s.p., in the Czech Republic.
  • Designed in accordance with NFPA 2001. This is the specific US standard governing clean agent extinguishing systems.
  • Manufactured at an ISO 9001 and ISO 14001 certified facility, also certified to AQAP 2110. AQAP 2110 is a NATO quality assurance standard for design, development, and production.

On MSHA and mine-specific requirements: Underground coal operations have their own diesel equipment fire suppression requirements under 30 CFR 75.1911, and surface mining and civil operations are governed by different, generally less prescriptive standards. If your site falls under MSHA jurisdiction, confirm with your safety director or MSHA district office whether a specific listing or approval is required for your application before treating any of this as a compliance checklist.

See Our Full List Of Certifications

Manage A Team Or Are You Looking At Procurement For A Contract?

We work directly with mining operators and civil contractors to fulfill their fire suppression needs. Simply email Dalton: dalton@blazecutusa.com for purchasing options or volume discounts!

FAQ

What is the BlazeCut T Series fire suppression system?

The BlazeCut T Series is an automatic, self-contained fire suppression system. It requires no wiring, no external power supply, and no separate storage cylinder. A heat-sensitive tube filled with pressurized FK-5-1-12 clean agent runs through the protected enclosure and acts as both the detection device and the agent storage container. When a fire develops, the tube melts at the hottest point and discharges the agent directly onto the fire source. The entire process is automatic and requires no human intervention.

How does the system detect a fire?

The BlazeCut tube continuously monitors the temperature of the entire space it runs through. When heat from a developing fire causes the tube to reach its actuation temperature, the tube ruptures at that exact location, right at the fire source, and releases the agent. There are no sensors, control boards, or wiring required for the standard T Series to activate.

Does the BlazeCut T Series need electricity to work?

No. The standard T Series operates completely independently of any power supply, 24 hours a day. This makes it well suited for protecting unoccupied spaces, equipment running after hours, engine compartments, and electrical enclosures where running wires is impractical or impossible. The optional pressure switch version can connect to an external signaling device if notification is needed, but the suppression system itself still does not require power to activate.

What extinguishing agent does BlazeCut USA carry?

BlazeCut USA carries the T Series charged exclusively with FK-5-1-12, also known by its chemical name Perfluoro(2-Methyl-3-Pentanone) and formerly marketed as Novec 1230. CAS number 756-13-8. It is a clean gaseous agent that is electrically non-conductive, non-corrosive, and leaves zero residue after discharge. It has zero ozone depletion potential and a global warming potential of 1.00 relative to CO2. FK-5-1-12 is listed in the US Toxic Substances Control Act (TSCA) inventory and is suitable for Class A, B, C, and electrical fire protection.

Does FK-5-1-12 leave a mess after the system fires?

No. FK-5-1-12 leaves absolutely no residue. There is no powder, no foam, and no water damage to deal with after the system activates. This is one of the main reasons it is the right choice for protecting electronics, server equipment, electrical control panels, and other sensitive equipment where a traditional extinguisher would cause serious secondary damage on top of whatever the fire already did.

Is FK-5-1-12 safe for people?

FK-5-1-12 is not classified as hazardous under standard conditions of use. Acute toxicity testing shows an oral and dermal LD50 greater than 2,000 mg/kg in rats and an inhalation LC50 greater than 1,227 mg/L over a 4-hour period. It is not listed as a carcinogen by NTP, IARC, or OSHA and has not been found to be mutagenic or toxic to reproduction. Standard precautions apply: avoid breathing vapors in an enclosed space at the time of discharge and ventilate the area before re-entry.

How difficult is it to install the BlazeCut T Series?

Installation is straightforward. The tube is secured inside the protected enclosure using heavy-duty cable ties or optional one-hole mounting clamps. No drilling, welding, or vehicle modifications are required. Each retail package includes the system, a user manual, cable ties, and warning labels. Most installations in engine compartments and electrical enclosures take under an hour.

Do I need a licensed technician to install it?

For most T Series applications, including engine compartments, electrical enclosures, small vehicles, and boats, installation does not require specialized tools or licensing. For fleet-wide deployments or larger commercial installations, we recommend working with an authorized BlazeCut dealer who can ensure proper sizing and placement. Visit our [Find a Dealer] page to locate one near you.

How do I figure out what size system I need?

System sizing is based on the volume of the enclosure being protected. Measure the width, height, and depth of the space in feet or meters to calculate the total volume. The smallest T Series option protects up to 3.18 cubic feet, and coverage scales up from there through the largest option, which protects up to 96.41 cubic feet for electrical fire applications and 73.45 cubic feet for engine fire applications. Coverage volumes are calculated at an ambient temperature of 68°F (20°C). If you are unsure which model is right for your application, email Dalton@blazecutusa.com and we can help you work through it.

What certifications does the BlazeCut T Series hold?

The BlazeCut T Series (6mm and 8mm BlazeTube configurations) is certified to LPS 1666 and carries CE approval. Systems have been independently performance tested at an accredited testing institute, Strojírenský zkušební ústav, s.p., in the Czech Republic, and are designed in accordance with NFPA 2001, the Standard on Clean Agent Fire Extinguishing Systems.

Is the BlazeCut T Series compliant with NFPA standards?

The T Series is designed in accordance with NFPA 2001, the Standard on Clean Agent Fire Extinguishing Systems. For specific compliance questions related to your facility, equipment, or local authority having jurisdiction (AHJ), we recommend consulting your AHJ directly or contacting us for guidance.

Is BlazeCut approved for the US market?

Yes. BlazeCut USA is the exclusive US importer and master distributor of BlazeCut fire suppression systems. The T Series is certified to LPS 1666 and CE approved, and the FK-5-1-12 agent is listed in the US TSCA inventory.

Can it protect an electric forklift or lithium battery compartment?

BlazeCut T Series systems can be deployed in the electrical and battery enclosures of electric forklifts and other electric-powered equipment. Lithium battery fires present specific suppression challenges, and the right system configuration depends on the enclosure size and layout. Email Dalton@blazecutusa.com to discuss the right setup for your fleet.

I am a distributor or catalog company. How do I carry BlazeCut?

BlazeCut USA is actively building its wholesale and dealer network across the country. If you are an industrial distributor, safety equipment supplier, or catalog company interested in stocking BlazeCut T Series systems, fill out the [Wholesale Partner Application] on our website or email Dalton@blazecutusa.com to start a conversation.

I manage a fleet or facility and need multiple units. Can I get volume pricing?

Yes. BlazeCut USA works with fleet managers, facilities teams, OEM manufacturers, and EHS departments to configure fire suppression programs across larger equipment inventories. Email Dalton@blazecutusa.com with details about your fleet or facility and we will connect you with the right resources.